Resistors
A resistor is an electronic component that reduces the flow of current in a circuit. It is used to limit the amount of current flowing through a circuit, or to create a voltage drop in a circuit. One of the main uses of resistors is to protect components from too much current, which can cause damage or failure. Flux.ai is the world's largest community-driven public library of resistors, with footprints, symbols, datasheets, and simulation models. Whether you're an engineer working on a new design, or a student learning about electronics, Flux.ai is the go-to resource for all things resistor-related. With a wealth of information and resources available, you'll find everything you need to know about resistors, and more.
MCP73831T-2ACI/OT
Charger IC Lithium Ion/Polymer SOT-23-5 The MCP73831/2 devices are highly advanced linear charge management controllers for use in spacelimited, cost-sensitive applications. The MCP73831/2 are available in an 8-Lead, 2 mm x 3 mm DFN package or a 5-Lead, SOT-23 package. Along with their small physical size, the low number of external components required make the MCP73831/2 ideally suited for portable applications. For applications charging from a USB port, the MCP73831/2 adhere to all the specifications governing the USB power bus. The MCP73831/2 employ a constant-current/constantvoltage charge algorithm with selectable preconditioning and charge termination. The constant voltage regulation is fixed with four available options: 4.20V, 4.35V, 4.40V or 4.50V, to accommodate new, emerging battery charging requirements. The constant current value is set with one external resistor. The MCP73831/2 devices limit the charge current based on die temperature during high power or high ambient conditions. This thermal regulation optimizes the charge cycle time while maintaining device reliability. Several options are available for the preconditioning threshold, preconditioning current value, charge termination value and automatic recharge threshold. The preconditioning value and charge termination value are set as a ratio or percentage of the programmed constant current value. Preconditioning can be disabled. Refer to Section 1.0 “Electrical Characteristics” for available options and the Product Identification System for standard options. The MCP73831/2 devices are fully specified over the ambient temperature range of -40°C to +85°C. Linear Charge Management Controller: - Integrated Pass Transistor - Integrated Current Sense - Reverse Discharge Protection • High-Accuracy Preset Voltage Regulation: + 0.75% • Four Voltage Regulation Options: - 4.20V, 4.35V, 4.40V, 4.50V • Programmable Charge Current: 15 mA to 500 mA • Selectable Preconditioning: - 10%, 20%, 40%, or Disable • Selectable End-of-Charge Control: - 5%, 7.5%, 10%, or 20% • Charge Status Output - Tri-State Output - MCP73831 - Open-Drain Output - MCP73832 • Automatic Power-Down • Thermal Regulation • Temperature Range: -40°C to +85°C • Packaging: - 8-Lead, 2 mm x 3 mm DFN - 5-Lead, SOT-23 Applications • Lithium-Ion/Lithium-Polymer Battery Chargers • Personal Data Assistants • Cellular Telephones • Digital Cameras • MP3 Players • Bluetooth Headsets • USB Chargers #commonpartslibrary #integratedcircuit #powermanagement #batterycharger
1.1k Uses0 StarsTPS62840DLCR
Buck Switching Regulator IC Positive Adjustable 1.8V 1 Output 750mA 8-VFDFN The TPS62840 is a high-efficiency step-down converter with ultra-low operating quiescent current of typically 60 nA. The device contains special circuitry to achieve just 120 nA IQ in 100% mode to further extend battery life near the end of discharge. The device uses DCS-Control to cleanly power radios and operates with a typical switching frequency of 1.8 MHz. In Power-Save Mode, the device extends the light load efficiency down to a load current range of 1 μA and below. 16 predefined output voltages can be selected by connecting a resistor to pin VSET, making the device flexible for various applications with a minimum amount of external components. The STOP pin of the device immediately eliminates any switching noise in order to take a noise-free measurement in test and measurement systems. The TPS62840 provides an output current of up to 750 mA. With an input voltage of 1.8 V to 6.5 V, the device supports multiple power sources such as 2S to 4S Alkaline, 1S to 2S Li-MnO2 , or 1S Li-Ion/LiSOCl2 Features 1• 60-nA operating quiescent current • 100% duty-cycle mode with 120-nA IQ • Input voltage range VIN from 1.8 V to 6.5 V • Output current up to 750 mA • RF friendly DCS-Control™ • 80% efficiency at 1 µA IOUT (3.6 VIN to 1.8 VOUT) • 16 selectable output voltages via VSET pin • Auto transition PFM/PWM or forced-PWM mode • Selectable forced PWM and STOP modes • Output discharge function • 25-nA shutdown current #commonpartslibrary #integratedcircuit #powermanagement #voltageregulator
301 Uses0 Stars
